# Overige Componenten

Documentatie over diverse elektronica componenten

# Bewegingssensoren

# HC-SR501 Bewegingssensor

[![HC-SR501-front.jpg](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/hc-sr501-front.jpg)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/hc-sr501-front.jpg)[![HC-SR501-back.jpg](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/hc-sr501-back.jpg)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/hc-sr501-back.jpg)

#### **Pin Configuration**

<figure class="wp-block-table" id="bkmrk-pin-number-pin-name-"><table><tbody><tr><td>**Pin Number**</td><td>**Pin Name**</td><td>**Description**</td></tr><tr><td>1</td><td>Vcc</td><td>Input voltage is +5V for typical applications. Can range from 4.5V- 12V</td></tr><tr><td>2</td><td>High/Low Ouput (Dout)</td><td>Digital pulse high (3.3V) when triggered (motion detected) digital low(0V) when idle(no motion detected</td></tr><tr><td>3</td><td>Ground</td><td>Connected to ground of circuit</td></tr></tbody></table>

</figure>[![HC-SR501-pinout.jpg](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/hc-sr501-pinout.jpg)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/hc-sr501-pinout.jpg)

#### **PIR Sensor Features**

- Wide range on input voltage varying from 4.V to 12V (+5V recommended)
- Output voltage is High/Low (3.3V TTL)
- Can distinguish between object movement and human movement
- Has to operating modes – Repeatable(H) and Non- Repeatable(H)
- Cover distance of about 120° and 7 meters
- Low power consumption of 65mA
- Operating temperature from -20° to +80° Celsius

#### **How to use PIR Motion Sensor**

The PIR sensor stands for Passive Infrared sensor. It is a low cost sensor which can detect the presence of Human beings or animals. This sensor has three output pins Vcc, Output and Ground as shown in the pin diagram above. Since the output pin is 3.3V TTL logic it can be used with any platforms like Arduino, Raspberry, [PIC](https://components101.com/pic16f877a-pin-diagram-description-features-datasheet), ARM, 8051 etc..

The module can be powered from voltage 4.5V to 20V but, typically 5V is used. Once the module is powered allow the module to calibrate itself for few minutes, 2 minutes is a well settled time. Then observe the output on the output pin. Before we analyse the output we need to know that there are two operating modes in this sensor such as Repeatable(H) and Non- Repeatable(L) and mode. The Repeatable mode is the default mode.

The output of the sensor can be set by shorting any two pins on the left of the module as shown below. You can also notice two orange colour potentiometers that can be used to set the sensitivity and time which will be explained further below.

#### **Repeatable(H) mode**

In Repeatable(H) mode the output pin Dout will go high (3.3V) when a person is detected within range and goes low after a particular time (time is set by “Off time control” potentiometer). In this mode the output pin will go high irrespective of whether the person is still present inside the range or has left the area. The sensitivity can be set using the “sensitivity control” potentiometer

#### **Non- Repeatable(L) mode**

In “I” mode the output pin Dout will go high (3.3V) when a person is detected within range and will stay high as long as he/she stays within the limit of the Sensors range. Once the person has left the area the pin will go low after the particular time which can be set using the potentiometer. The sensitivity can be set using the “sensitivity control” potentiometer

There are two important materials present in the sensor one is the pyroelectric crystal which can detect the heat signatures from a living organism (humans/animals) and the other is a Fresnel lenses which can widen the range of the sensor. Yes the white colour things is just a lense that is used to widen the range of the sensor, if you remove the lense you can find the Pyroelectric sensor inside it covered inside a protective metal casing as shown above.

###### BRON:

[Components101](https://components101.com/sensors/hc-sr501-pir-sensor)

# Spanningsregelaars

# AMS1117 Spanningsregelaar

[![afbeelding.png](https://www.linuxfun.nl/uploads/images/gallery/2023-08/scaled-1680-/afbeelding.png)](https://www.linuxfun.nl/uploads/images/gallery/2023-08/afbeelding.png)

#### **Pin Configuration**

<figure class="wp-block-table" id="bkmrk-pin-number-pin-name-"><table><tbody><tr><td>**Pin Number**</td><td>**Pin Name**</td><td>**Description**</td></tr><tr><td>1</td><td>Adjust/Ground</td><td>This pins adjusts the output voltage, if it is a fixed voltage regulator it acts as ground</td></tr><tr><td>2</td><td>Output Voltage (Vout)</td><td>The regulated output voltage set by the adjust pin can be obtained from this pin</td></tr><tr><td>3</td><td>Input Voltage (Vin)</td><td>The input voltage</td></tr></tbody></table>

</figure>#### **Features**

- Fixed/Adjustable 3-terminal Linear voltage regulator
- Low Drop-Out (LDO) Voltage regulator
- Fixed Voltage type: 1.5V, 1.8V, 2.5V, 2.85V, 3.3V and 5V
- Variable Voltage range: 1.25V to 13.8V
- Output current is 1000mA
- Maximum Drop-out Voltage: 1.3V
- In-built Current Limiting and thermal protection.
- Operating junction temperature is 125°C
- Available in SOT-223, TO-252 and SO-8 Package

[![AMS1117-schema.png](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/ams1117-schema.png)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/ams1117-schema.png)

[![AMS1117-module.jpg](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/ams1117-module.jpg)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/ams1117-module.jpg)

#### **Applications**

- Used for Positive voltage regulations
- Variable power supply
- Current limiting circuits
- Reverse polarity circuits
- Commonly used in Desktop PC, DVD and other consumer products
- Used in motor control circuits

###### BRON:

[Components101](https://components101.com/regulators/ams1117-1a-ldo-regulator-pinout-datasheet)

# Temperatuur sensoren

# DHT22 temperatuur en vochtigheid sensor

[![DHT22-Sensor-Pinout.png](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/dht22-sensor-pinout.png)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/dht22-sensor-pinout.png)

#### **Pin Identification and Configuration**

<figure class="wp-block-table" id="bkmrk-no%3A-pin-name-descrip"><table><tbody><tr><td>**No:**</td><td>**Pin Name**</td><td>**Description**</td></tr><tr><td>**For DHT22 Sensor**</td></tr><tr><td>1</td><td>Vcc</td><td>Power supply 3.5V to 5.5V</td></tr><tr><td>2</td><td>Data</td><td>Outputs both Temperature and Humidity through serial Data</td></tr><tr><td>3</td><td>NC</td><td>No Connection and hence not used</td></tr><tr><td>4</td><td>Ground</td><td>Connected to the ground of the circuit</td></tr><tr><td>**For DHT22 Module**</td></tr><tr><td>1</td><td>Vcc</td><td>Power supply 3.5V to 5.5V</td></tr><tr><td>2</td><td>Data</td><td>Outputs both Temperature and Humidity through serial Data</td></tr><tr><td>3</td><td>Ground</td><td>Connected to the ground of the circuit</td></tr></tbody></table>

[![DHT22-pcb.jpg](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/dht22-pcb.jpg)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/dht22-pcb.jpg)

#### **DHT22 Specifications**

- Operating Voltage: 3.5V to 5.5V
- Operating current: 0.3mA (measuring) 60uA (standby)
- Output: Serial data
- Temperature Range: -40°C to 80°C
- Humidity Range: 0% to 100%
- Resolution: Temperature and Humidity both are 16-bit
- Accuracy: ±0.5°C and ±1%

</figure>###### BRON:

[Components101](https://components101.com/sensors/dht22-pinout-specs-datasheet)

<figure class="wp-block-table" id="bkmrk-%C2%A0-1"></figure>

# DS18B20 temperatuur sensor

[![DS18B20-pinout.jpg](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/ds18b20-pinout.jpg)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/ds18b20-pinout.jpg)

[![DS18B20-ESP8266.jpg](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/ds18b20-esp8266.jpg)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/ds18b20-esp8266.jpg)

[![DS18B20-Circuit-Diagram.png](https://www.linuxfun.nl/uploads/images/gallery/2023-09/scaled-1680-/ds18b20-circuit-diagram.png)](https://www.linuxfun.nl/uploads/images/gallery/2023-09/ds18b20-circuit-diagram.png)

#### **DS18B20 Sensor Specifications**

- Programmable Digital Temperature Sensor
- Communicates using 1-Wire method
- Operating voltage: 3V to 5V
- Temperature Range: -55°C to +125°C
- Accuracy: ±0.5°C
- Output Resolution: 9-bit to 12-bit (programmable)
- Unique 64-bit address enables multiplexing
- Conversion time: 750ms at 12-bit
- Programmable alarm options
- Available as To-92, SOP and even as a waterproof sensor

###### BRON:

[Components 101](https://components101.com/sensors/ds18b20-temperature-sensor)

# Webshops

# Domotica en Elektronica webshops

- [AliExpress](https://www.aliexpress.com)
- [Banggood](https://www.banggood.com)
- [Bits &amp; Parts](https://www.bitsandparts.nl/)
- [DomoticX](https://webshop.domoticx.nl/)
- [Ebay - TechcrunchFR](https://www.ebay.nl/str/techcrunchfr)
- [Ebay - Dir-Arduino](https://www.ebay.nl/str/diyarduino)
- [Gadgetbouw.nl](https://www.gadgetbouw.nl/)
- [HobbyElectronica](https://www.hobbyelectronica.nl/)
- [Opencircuit](https://opencircuit.nl/)
- [Vanallesenmeer](https://www.vanallesenmeer.nl/)